ZHANG Xin,SONG Jiyuan,DING Tao,et al.Study on Uniformity of the Airflow Field in a Turbulent Ball Tower for Purification of Hot Press Exhaust Gas from Fiberboard Manufacturing[J].Chinese Journal of Wood Science and Technology,2024,38(04):66-71.
ZHANG Xin,SONG Jiyuan,DING Tao,et al.Study on Uniformity of the Airflow Field in a Turbulent Ball Tower for Purification of Hot Press Exhaust Gas from Fiberboard Manufacturing[J].Chinese Journal of Wood Science and Technology,2024,38(04):66-71. DOI: 10.12326/j.2096-9694.2024057.
Study on Uniformity of the Airflow Field in a Turbulent Ball Tower for Purification of Hot Press Exhaust Gas from Fiberboard Manufacturing
To improve the purification efficiency of the turbulent ball tower for removing formaldehyde from fiberboard hot pressing exhaust gas
the authors evaluated the effect of the perforation ratio of the support plate on the uniformity of the gas flow field inside the tower. The results showed that the support plate’s perforation ratio had a significant impact on the velocity distribution and pressure consumption of the gas flow field inside the tower. When the perforation ratio of the support plate was 53.3%
the uniformity of the airflow field reached its optimum (CV value of 0.295)
and the pressure consumption was relatively small at 32 Pa
which could effectively drive the packing balls into a fluidized state uniformly. The verification experiment showed that the average concentration of formaldehyde at the outlet of the turbulence tower decreased compared to before the improvement
and the purification efficiency of the device was significantly improved. The result provides research ideas and experimental data for the optimization design of other structures in the turbulence tower of the exhaust purification system for fiberboard production.
关键词
纤维板湍球塔支承板开孔率气体流场均匀性数值模拟
Keywords
fiberboardturbulent ball towerperforation ratio of the support plateairflow uniformitynumerical simulation
ZHANG Z Y. Analysis of the development situation of the fiberboard industry in China[J]. Forestry Machinery & Woodworking Equipment, 2022, 50(7): 11-15, 23.
DING T, ZHU N F, LIU X Y, et al. Characteristics and abatement technologies of medium density fiberboard hot-press emissions[J]. Chinese Journal of Wood Science and Technology, 2021, 35(1): 59-63.
OKASHA F, HEGAZI A A, RASHID A G. An investigation on drying process in a novel configuration of fluidized bed[J]. Mansoura Engineering Journal, 2015, 40(4): 12-24.
LI H W, DUAN W B, WANG S B, et al. Numerical simulation study on different spray rates of three-area water distribution in wet cooling tower of fossil-fuel power station[J]. Applied Thermal Engineering, 2018, 130: 1558-1567.
HEIDARINEJAD G, KARAMI M, DELFANI S. Numerical simulation of counter-flow wet-cooling towers[J]. International Journal of Refrigeration, 2009, 32(5): 996-1002.
CHEN X H, SUN F Z, CHEN Y L, et al. Novel method for improving the cooling performance of natural draft wet cooling towers[J]. Applied Thermal Engineering, 2019, 147: 562-570.
JONES W P, LAUNDER B E. The prediction of laminarization with a two-equation model of turbulence[J]. International Journal of Heat and Mass Transfer, 1972, 15(2): 301-314.
DURST F, LAUNDER B E, SCHMIDT F W, et al. Turbulent shear flows 4: Selected papers from the fourth international on symposium on turbulent shear flows[C]// Proceedings of the 11th Symposium on Turbulent Shear Flows, France,1997.
LIU Y, YE X M, YANG T K, et al. Numerical study on droplet breakage and particle distribution in rotating nebulizers[J]. Electric Power Science and Engineering, 2023, 39(4): 69-78.
MA W Y, LIU J H, ZHANG X B, et al. Reynolds number effect on aerodynamic characteristics of a rotating circular cylinder[J]. Journal of Vibration and Shock, 2022, 41(7): 46-52.