1.Yangzhou Polytechnic Institute，Yangzhou 225100，Jiangsu，China
2.Yangzhou University，Yangzhou 225100， Jiangsu，China
3.Nanjing Forestry University，Nanjing 210037， Jiangsu，China
4.Inner Mongolia Agricultural University，Huhhot 010018，Inner Mongolia，China
扫 描 看 全 文
薛莹莹,朱旭东,张雪雯等.水青冈木-自攻螺钉复合榫连接节点单剪性能[J].木材科学与技术,2022,36(01):68-74.
XUE Ying-ying,ZHU Xu-dong,ZHANG Xue-wen,et al.Single Shear Performance of Components Connected by Beech-self-Tapping-Screw Composite Dowels[J].Chinese Journal of Wood Science and Technology,2022,36(01):68-74.
对比研究自攻螺钉、水青冈木榫和水青冈木-自攻螺钉复合榫3种连接节点的单剪承载性能，采用特征值分析法对单剪力-位移进行分析，获得最大荷载、极限荷载、屈服荷载、初始刚度、延性系数、能耗和最终位移等七个参数。结果表明：1）除了初始刚度，采用自攻螺钉的连接节点承载性能优于水青冈木榫连接节点；2）复合榫连接节点的承载力呈现两个极大值峰，第一个极大值高于水青冈木榫连接节点最大值2 kN，第二个极大值高于自攻螺钉连接节点最大值0.7 kN；3）复合榫连接节点的最终位移介于水青冈木榫连接节点和自攻螺钉连接节点之间，耗能能力和自攻螺钉连接节点相当，其他参数均优于自攻螺钉连接节点和水青冈木榫连接节点。综合参数分析，水青冈木-自攻螺钉复合榫能够有效结合自攻螺钉和水青冈木榫的优良特性。
This article studied the shear performance of structural components with three connection modes, including two self-tapping screws, beech dowels, and beech-self-tapping-screw composite dowels. The simple shear test was conducted with each specimen. The force-displacement curve was analyzed by the method of characteristic values. Seven parameters were obtained, including the maximum load, ultimate load, yield load, initial stiffness, ductility coefficient, energy consumption, and final displacement. The results showed: 1) The parameters of the components connected by self-tapping screws were better than those of beech dowels, except the initial stiffness. 2) Two peak values were found in the curves of the components connected by the beech-self-tapping-screw composite dowels. The first peak value was 2 kN higher than the maximum load of the components connected by the beech dowels. The second peak value was 0.7 kN higher than the maximum load of the components connected by the self-tapping screws. 3) The final displacement value of the components connected by the composite dowels was between the components connected by beech dowels and self-tapping screws. The energy consumption was similar to the self-tapping screws. The rest of parameters of the composite dowels were better than those of beech dowels and self-tapping screws. Based on the study, the composite dowels can combine the good characteristics of both the beech dowels and self-tapping screws.
水青冈木-自攻螺钉复合榫自攻螺钉水青冈木榫单剪性能特征值分析法
beech-self-tapping-screw composite dowelself-tapping screwbeech dowelsingle shear performanceanalysis method of characteristic value
王洁，靳慧. 木材摩擦焊接技术的研究进展[J]. 西北林学院学报, 2019, 34(6): 191-196.
WANG J, JIN H. Research progress of wood friction welding technology[J]. Journal of Northwest Forestry University, 2019, 34(6): 191-196.
罗翔亚，朱旭东，张吉荣，等. 木材焊接理论研究及技术进展[J]. 西北林学院学报, 2017, 32(6): 270-275.
LUO X Y, ZHU X D, ZHANG J R, et al. Theoretical research and technical progress of wood welding[J]. Journal of Northwest Forestry University, 2017, 32(6): 270-275.
周晓剑，Antonio P，杜官本. 木材焊接技术（无胶胶合）的研究进展[J]. 中国胶粘剂, 2014, 23(6): 47-53.
ZHOU X J, Antonio P, DU G B, et al. Research progress of wood welding technology (bonding without adhesive)[J]. China Adhesives, 2014, 23(6): 47-53.
朱海，陈家瑞，张剑，等. 木榫旋转摩擦焊接抗拉拔力的影响因素[J]. 东北林业大学学报，2020，48(6): 75-79.
ZHU H, CHEN J R, ZHANG J, et al. Influencing factors of pullout resistance on wood-dowel rotary friction welding[J]. Journal of Northeast Forestry University, 2020, 48(6): 75-79.
朱旭东，薛莹莹，张苏俊，等. 焊接时间和氯化铜处理对木榫焊接性能的影响机制[J]. 西北林学院学报，2019，34(5)：231-239.
ZHU X D, XUE Y Y, ZHANG S J, et al. Influence mechanisms of welding time and CuCl2 treatment on the weldability of dowels[J]. Journal of Northwest Forestry University, 2019, 34(5): 231-239.
刘恪. 压缩木销旋转摩擦焊接抗拔性能研究[D]. 大连理工大学，2019：34-48.
Bocquet J F, Pizzi A, Resch L. Full-scale industrial wood floor assembly and structures by welded-through dowels[J]. European Journal of Wood and Wood Products, 2007, 65(2): 149-155.
Bocquet J F, Pizzi A, Despres A, et al. Wood joints and laminated wood beams assembled by mechanically-welded wood dowels[J]. Journal of Adhesion Science and Technology, 2007, 21(3/4): 301- 317.
Satoshi F, Keita O, Masaki N, et al. Shear properties of metal-free wooden load-bearing walls using plywood jointed with a combination of adhesive tape and wood dowels[J]. European Journal of Wood and Wood Products, 2017, 75(3): 429-437.
Girardon S, Barthram C, Resch L, et al. Determination of shearing stiffness parameters to design multi-layer spruce beams using welding-through wood dowels[J]. European Journal of Wood and Wood Products, 2014, 72(6): 721-733.
HAO J X, XU L, WU X F, et al. Analysis and modeling of the dowel connection in wood T type joint for optimal performance[J]. Composite Structures, 2020, 253: 1-11.
王必林. 压缩木销钉连接力学性能研究[D]. 大连理工大学，2020：63-73.
李桥，宋焕，王志强. 竹/木销连接组合木梁抗弯性能研究[J]. 西北林学院学报，2020，35(2)：218-222.
LI Q, SONG H, WANG Z Q. Bending performance of timber composite beam fastened with bamboo/wood dowels[J]. Journal of Northwest Forestry University, 2020, 35(2): 218-222.
ZHU X D, XUE Y Y, SHEN Jet al. Withdrawal strength of welded dowel joints made of birch and larch wood[J]. Wood Research, 2019, 64(5): 921-934.
殷天啸，桂涛，刘艺肖，等. 国产自攻螺钉抗钉帽拉穿强度研究[J]. 林产工业，2020，57(4)：29-32.
YIN T X, GUI T, LIU Y X, et al. Study on head pull-through strength of domestic self-tapping screws[J]. China Forest Products Industry, 2020, 57(4):29-32.
滕启城，王菲彬，阙泽利，等. 圆钢钉和自攻螺钉钉入角度对规格材握钉力性能的影响[J]. 林业科学，2019，56(1)：154-161.
TENG Q C, WANG F B, QUE Z L, et al. Effects of angles on the screw and nail withdrawal strength in dimension lumber[J]. Scientia Silvae Sinicae, 2019, 56(1): 154-161.
左宏亮，刘翰然，鲁建鑫. 新型自攻螺钉加固措施对胶合木梁受弯性能的影响[J]. 东北林业大学学报，2020，48(5): 112-116.
ZUO H L, LIU H R, LU J X. Effect of new self-tapping screw reinforcement measures on bending performance of glulam beams[J]. Journal of Northeast Forestry University, 2020, 48(5): 112-116.
鹿相戎，滕启城，李哲瑞，等. 云杉胶合木钢板斜螺钉连接的剪切性能研究[J]. 林业工程学报，2020，5(3)：48-53.
LU X R, TENG Q C, LI Z R, et al. Study on shear property of spruce glulam and steel plate connected with inclined screw[J]. Journal of Forestry Engineering, 2020, 5(3): 48-53.
唐立秋，徐伟，杨会峰，等. 自攻螺钉增强胶合木横纹承压性能试验[J]. 南京工业大学学报(自然科学版)，2021，43(1)：94-100.
TANG L Q, XU W, YANG H F, et al. Compressive strength tests perpendicular to the grain of glulam reinforced with self-tapping screws[J]. Journal of Nanjing Tech University (Natural Science Edition), 2021, 43(1): 94-100.
常程，方毅飞，刘义凡，等. 斜螺钉在正交胶合木中的抗拔性能研究[J]. 建筑技术，2019，50(4)：416-418.
CHANG C, FANG Y F, LIU Y F, et al. Study on pull-out performance of tilted self-tapping screw in cross-laminated timber[J]. Architecture Technology, 2019, 50(4): 416-418.
董惟群，姚悦，宋焕，等. 自攻螺钉连接正交胶合木抗剪承载力研究[J]. 木材工业，2018，32(5)：1-5.
DONG W Q, YAO Y, SONG H, et al. Shear strength of cross-laminated timber connected with self-tapping screws[J]. China Wood Industry, 2018, 32(5): 1-5.
林沁雨，文程生，刁玥，等. 自攻螺钉与榫卯连接CLT墙体节点力学性能研究[J]. 北京林业大学学报，2019，41(11)：146-154.
LIN Q Y, WEN C S, DIAO Y, et al. Mechanical properties of CLT shear connections between self-tapping screws and mortise tenons[J]. Journal of Beijing Forestry University, 2019, 41(11): 146-154.
孙兆洋，程小武，陆伟东. 钢板-自攻螺钉加固残损古建筑木结构直榫节点抗震性能试验研究[J]. 结构工程师，2018，34(5)：106-112.
SUN Z Y, CHENG X W, LU W D, et al. Experimental study on seismic performance of damaged straight mortise-tenon joints of ancient timber buildings strengthened with steel plates and self-tapping screws[J]. Structural Engineers, 2018, 34(5): 106-112.
Silva C, Branco J M, Ringhofer A, et al. The influence of moisture content variation, number and width of gaps on the withdrawal resistance of self tapping screws inserted in cross laminated timber[J]. Construction and Building Materials, 2016, 125: 1205-1215.
Structural design guidelines for wood frame construction (in Japanese) [M]. Japan 2×4 Home Builders Association, Tokyo, 2002: 213-241.
相关文章
相关作者
相关机构
京公网安备11010802024621